[vanlife]

Okay, last update on this! I
Okay, last update on this! I spoke with one of the guys at Fiberine in California (http://www.fiberine.com) and he was very generous to donate some advice. He said that those cages are unique to ambulance vans for safety, and that it is, in fact, there in case of impact. So long as I’m not planning on any ambulance activities and getting stopped by the police while at it, I should be fine to remove it all together.

Whew! Frankly, that’s the answer I wanted. I’ll get another half-inch out of the van for myself and I get to cut this thing out and get moving again.

[vanlife]

Okay, last update on this! I
Okay, last update on this! I spoke with one of the guys at Fiberine in California (http://www.fiberine.com) and he was very generous to donate some advice. He said that those cages are unique to ambulance vans for safety, and that it is, in fact, there in case of impact. So long as I’m not planning on any ambulance activities and getting stopped by the police while at it, I should be fine to remove it all together.

Whew! Frankly, that’s the answer I wanted. I’ll get another half-inch out of the van for myself and I get to cut this thing out and get moving again.

[vanlife]

Update… can I get another
Update… can I get another opinion?

I went with (3) for the day. I unbolted the cage, bought some stock, 1″ square steel to use to raise it up and cut it into appropriate 3″ and 4″ lengths to fit beneath the existing feet of the cage.

1) The cage is no precision piece of engineering. One of the legs is longer than all others by, I’d guess, ~ 1/8″. I have to cut this one off if I raise it because otherwise the front-left corner jams in to the roof, hard. I think this is okay, this is the only leg that does not have a twin on the opposite side… okay, so that’s fair.

2) Putting in new bolts or self-tapping screws. I choose one or the other based on access, preferring bolts where I can. I’ll be able to get at all but one of the feet, maybe I can come up with something to make this work still.

Taking a breath and examining the whole outfit, I cannot imagine that this served anything more than to hold up the interior shell wall. It’s 1″+ clearance to the roof at all times, and most feet had only one bolt/screw, I think two had two in them.

I’m back on the fence after today, thinking I should just take the whole thing out and build a new interior cage out of wood to hold up my roof and insulation. Before going that route was hoping to solicit one or two more opinions. The only way I can get the cage out is by cutting it out with the angle grinder and that’s a one-way road.

Aaron

[vanlife]

Update… can I get another
Update… can I get another opinion?

I went with (3) for the day. I unbolted the cage, bought some stock, 1″ square steel to use to raise it up and cut it into appropriate 3″ and 4″ lengths to fit beneath the existing feet of the cage.

1) The cage is no precision piece of engineering. One of the legs is longer than all others by, I’d guess, ~ 1/8″. I have to cut this one off if I raise it because otherwise the front-left corner jams in to the roof, hard. I think this is okay, this is the only leg that does not have a twin on the opposite side… okay, so that’s fair.

2) Putting in new bolts or self-tapping screws. I choose one or the other based on access, preferring bolts where I can. I’ll be able to get at all but one of the feet, maybe I can come up with something to make this work still.

Taking a breath and examining the whole outfit, I cannot imagine that this served anything more than to hold up the interior shell wall. It’s 1″+ clearance to the roof at all times, and most feet had only one bolt/screw, I think two had two in them.

I’m back on the fence after today, thinking I should just take the whole thing out and build a new interior cage out of wood to hold up my roof and insulation. Before going that route was hoping to solicit one or two more opinions. The only way I can get the cage out is by cutting it out with the angle grinder and that’s a one-way road.

Aaron

[vanlife]

Darren,
Darren,

Thank you!! On all counts, especially as I’m notorious for second-guessing myself so I appreciate the thumbs-up on vehicle choice and work so far. I’ve got a late start today, going to to see just how effective I can be at releasing and raising the structure… then off to find some stock steel I hope 🙂

Further opinions/comments definitely welcomed still…

Cheers!

[vanlife]

Darren,
Darren,

Thank you!! On all counts, especially as I’m notorious for second-guessing myself so I appreciate the thumbs-up on vehicle choice and work so far. I’ve got a late start today, going to to see just how effective I can be at releasing and raising the structure… then off to find some stock steel I hope 🙂

Further opinions/comments definitely welcomed still…

Cheers!

[Author]

Posts