Forum Replies Created
- AuthorPosts
- BluebirdParticipant
Floor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantFloor base
Hello thereThese floor bases are usually just held down with a ring of screws (visible around the top?) although they might have rusted to the floor over time. The base itself is made of aluminium, so it won’t have rusted in itself – although road salts might have attacked it and caused it to corrode and the dissimilar metals to react and sieze the screws over the years too.
Most manufacturers just cut a rough hole through the floor when they fit these and the base is clearly visible below. If you locate it, you should be able to verify that it is just screwed down. WD40 both sides and patience to unscrew; then a big hammer and brute force to knock the screws through if that doesn’t work should do the trick. You shouldn’t need any special tools and you should be able to reuse it without any problem. If not, they are readily available in camping stores and cheap on ebog.
Good luck, I had a couple of Midi vans a few years ago and found them very enjoyable and practical vans to run – nice to know at least one has survived.
BluebirdParticipantTachograph
Hello thereA tachograph is only necessary if the vehicle is to be used for commercial purposes. If the use is entirely private then you can forget it, as you no longer have restrictions on your driving hours (or a boss to check them afterwards and a potential fine..!)
You might find that the tacho will need a sheet installed behind the speedo or it will give you odd readings – often the needle will jump right around the dial and stay there. I’ve had a few in the past like this – others have been fine without anything.
Hope this helps
- AuthorPosts